Exabyte MAGNUM 1X7 LTO Manuel d'utilisateur Page 107
- Page / 162
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
OCTOBER 2006 MAGNUM 1X7 LTO AUTOLOADER
91
7
MAINTENANCE
This chapter describes basic autoloader maintenance tasks that you can
perform on-site without the aid of a service technician. These tasks include:
Replacing the tape drive
Cleaning the autoloader
Upgrading autoloader firmware and creating diagnostic listings via FTP
Upgrading autoloader firmware and creating diagnostic listings using
Exabyte LibTool
Upgrading tape drive firmware and creating diagnostic listings using
Exabyte LTOTool.
REPLACING THE TAPE DRIVE
This section describes how to replace the autoloader’s tape drive. You can
order a new tape drive from Exabyte (see page iii) or from your supplier.
Caution
Do not attempt to replace any components in the autoloader, other than the tape
drive. If you do so, you will void your warranty.
!
! !
! Important
New tape drives must be specially configured for use in the
autoloader and must therefore be ordered directly from Exabyte
or from an Exabyte-approved supplier.
You must replace the installed tape drive with the same
configuration tape drive, as follows:
Full height to full height
-or-
Half height to half height
You cannot replace a full height with a half height, or vice versa.
- PRODUCT MANUAL 1
- ONTACTING 3
- Contents 5
- Product Overview 9
- Installing the Autoloader 9
- Configuring the Autoloader 9
- Autoloader Operation 10
- Maintenance 10
- Shipping the Autoloader 10
- ABOUT THIS MANUAL 13
- RELATED PUBLICATIONS 14
- PRODUCT OVERVIEW 17
- AUTOLOADER COMPONENTS 18
- BACK PANEL COMPONENTS 19
- INTERNAL COMPONENTS 20
- UTOLOADER COMPONENTS 21
- CHAPTER 1—PRODUCT OVERVIEW 22
- INSTALLING THE AUTOLOADER 23
- Remove this label 24
- Shipping 24
- Advertencia 27
- ASSEMBLING THE RAILS 28
- Insert screw here 31
- SCSI connectors 33
- SCSI terminator 34
- Ethernet port 34
- Power cord connection 35
- Power switch 35
- CONFIGURING THE 37
- AUTOLOADER 37
- Viewing the Home Screen 38
- Up a Level 39
- Next Choice 39
- Previous Choice 39
- Down a Level 39
- OVERVIEW OF AUTOLOADER MENUS 40
- Home Screen 41
- SETTING CONFIGURATION OPTIONS 42
- CHANGING THE LCD LANGUAGE 43
- CHANGING THE LCD CONTRAST 44
- CHANGING THE SCSI IDS 45
- Tape Drive SCSI ID 46
- CHANGING THE EMULATION MODE 47
- Enabling the Autoclean Option 50
- ETTING CONFIGURATION OPTIONS 51
- C h a n g e I P A d d r ? 52
- D H C P I s O N 52
- C h a n g e a 52
- C o n f i g u r a t i o n 52
- E n t e r P a s s w o r d 58
- Important 60
- CHECKING THE SETUP 61
- USING THE REMOTE 63
- MANAGEMENT UTILITY 63
- LIBRARY INFORMATION 65
- LIBRARY STATUS 66
- TAPE DRIVE STATUS 67
- INVENTORY 67
- CHANGE LIBRARY CONFIGURATION 71
- CHANGE ETHERNET CONFIGURATION 72
- CHANGE WEB ACCESS PASSWORD 74
- RUNNING DIAGNOSTICS 75
- 76
- AUTOLOADER OPERATION 77
- Cartridge 78
- PREPARING CARTRIDGES 79
- HAPTER 5—AUTOLOADER OPERATION 80
- Access hole for operating the 83
- L o a d D r i v e 84
- CLEANING THE TAPE DRIVE 86
- L T O 1 x 7 2 U 87
- D : N e e d s C l e a n i n g 87
- RESETTING THE AUTOLOADER 90
- RUNNING SYSTEM DEMOS 91
- PERFORMING DIAGNOSTIC TESTS 93
- STORING CARTRIDGES 94
- VIEWING AUTOLOADER 95
- INFORMATION 95
- RODUCT MANUAL 1012581 100
- C e l l # n B a r c o d e 103
- S e l e c t a C o m m a n d 103
- VIEWING CELL STATISTICS 104
- IEWING CELL STATISTICS 105
- VIEWING THE EVENT LOG 106
- MAINTENANCE 107
- PREPARING FOR REPLACEMENT 108
- REMOVING THE TAPE DRIVE 109
- Serial cable 110
- SCSI cable 110
- Power cable 110
- ! Important 111
- Unload button 112
- EPLACING THE TAPE DRIVE 113
- Air block plate– 114
- CLEANING THE AUTOLOADER 115
- PRODUCT MANUAL 1012581 116
- TROUBLESHOOTING 119
- SCSI BUS INFORMATION 126
- OPERATING SYSTEM INFORMATION 127
- DIAGNOSTIC INFORMATION 127
- ADVANCED TROUBLESHOOTING 128
- SHIPPING THE AUTOLOADER 129
- Remove this screw 130
- (one each side) 130
- Insert shipping key here 131
- Foam spacers 133
- SPECIFICATIONS 135
- PERFORMANCE SPECIFICATIONS 136
- CARTRIDGE INVENTORY TIMES 137
- MOVE COMPLETE TIME 137
- RELIABILITY 137
- POWER SPECIFICATIONS 138
- ENVIRONMENTAL SPECIFICATIONS 139
- ACOUSTIC NOISE LIMITS 140
- SHOCK AND VIBRATION LIMITS 140
- SHIPPING SPECIFICATIONS 141
- CANADIAN VERIFICATION 142
- EUROPEAN COMMUNITY 142
- USTRALIA AND NEW ZEALAND 143
- APPENDIX A—SPECIFICATIONS 144
- WRITE ONCE, READ MANY 145
- (WORM) CAPABILITY 145
- DATA SECURITY ON WORM MEDIA 146
- WORM MEDIA ERRORS 146
- REQUIREMENTS 147
- TAPEALERT FLAGS 147
- ERROR CODES 148
- ERROR MESSAGES 149
- APE ALERT FLAGS 151
- APPENDIX C—ERROR MESSAGES 154
- PRODUCT LIMITED WARRANTY 161
- ON SITE SERVICE (OSS) 161
- WARRANTY 162
© 2020, manymanuals.fr. Tous droits réservés | 1.453 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels