Exabyte MAGNUM 1X7 LTO Manuel d'utilisateur Page 37
- Page / 162
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
OCTOBER 2006 MAGNUM 1X7 LTO AUTOLOADER
21
3
CONFIGURING THE
AUTOLOADER
After installing the autoloader hardware, you are ready to set configuration
options. This chapter describes how to:
Access configuration options
Set configuration options
Check the setup
ACCESSING CONFIGURATION OPTIONS
With the Magnum 1x7 LTO Autoloader you can use the operator panel or the
autoloader’s web-based Remote Management utility to access configuration
options. If you plan to use the Remote Management utility, refer to Chapter 4.
USING THE OPERATOR PANEL
The autoloader’s operator panel includes a two-line LCD and keypad (see
Figure 3-1) that allow you to interactively control autoloader operations. Using
the operator panel, you can set autoloader options, check operating statistics,
and diagnose errors.
Figure 3-1 Autoloader LCD and keypad
LCD
Keypad
- PRODUCT MANUAL 1
- ONTACTING 3
- Contents 5
- Product Overview 9
- Installing the Autoloader 9
- Configuring the Autoloader 9
- Autoloader Operation 10
- Maintenance 10
- Shipping the Autoloader 10
- ABOUT THIS MANUAL 13
- RELATED PUBLICATIONS 14
- PRODUCT OVERVIEW 17
- AUTOLOADER COMPONENTS 18
- BACK PANEL COMPONENTS 19
- INTERNAL COMPONENTS 20
- UTOLOADER COMPONENTS 21
- CHAPTER 1—PRODUCT OVERVIEW 22
- INSTALLING THE AUTOLOADER 23
- Remove this label 24
- Shipping 24
- Advertencia 27
- ASSEMBLING THE RAILS 28
- Insert screw here 31
- SCSI connectors 33
- SCSI terminator 34
- Ethernet port 34
- Power cord connection 35
- Power switch 35
- CONFIGURING THE 37
- AUTOLOADER 37
- Viewing the Home Screen 38
- Up a Level 39
- Next Choice 39
- Previous Choice 39
- Down a Level 39
- OVERVIEW OF AUTOLOADER MENUS 40
- Home Screen 41
- SETTING CONFIGURATION OPTIONS 42
- CHANGING THE LCD LANGUAGE 43
- CHANGING THE LCD CONTRAST 44
- CHANGING THE SCSI IDS 45
- Tape Drive SCSI ID 46
- CHANGING THE EMULATION MODE 47
- Enabling the Autoclean Option 50
- ETTING CONFIGURATION OPTIONS 51
- C h a n g e I P A d d r ? 52
- D H C P I s O N 52
- C h a n g e a 52
- C o n f i g u r a t i o n 52
- E n t e r P a s s w o r d 58
- Important 60
- CHECKING THE SETUP 61
- USING THE REMOTE 63
- MANAGEMENT UTILITY 63
- LIBRARY INFORMATION 65
- LIBRARY STATUS 66
- TAPE DRIVE STATUS 67
- INVENTORY 67
- CHANGE LIBRARY CONFIGURATION 71
- CHANGE ETHERNET CONFIGURATION 72
- CHANGE WEB ACCESS PASSWORD 74
- RUNNING DIAGNOSTICS 75
- 76
- AUTOLOADER OPERATION 77
- Cartridge 78
- PREPARING CARTRIDGES 79
- HAPTER 5—AUTOLOADER OPERATION 80
- Access hole for operating the 83
- L o a d D r i v e 84
- CLEANING THE TAPE DRIVE 86
- L T O 1 x 7 2 U 87
- D : N e e d s C l e a n i n g 87
- RESETTING THE AUTOLOADER 90
- RUNNING SYSTEM DEMOS 91
- PERFORMING DIAGNOSTIC TESTS 93
- STORING CARTRIDGES 94
- VIEWING AUTOLOADER 95
- INFORMATION 95
- RODUCT MANUAL 1012581 100
- C e l l # n B a r c o d e 103
- S e l e c t a C o m m a n d 103
- VIEWING CELL STATISTICS 104
- IEWING CELL STATISTICS 105
- VIEWING THE EVENT LOG 106
- MAINTENANCE 107
- PREPARING FOR REPLACEMENT 108
- REMOVING THE TAPE DRIVE 109
- Serial cable 110
- SCSI cable 110
- Power cable 110
- ! Important 111
- Unload button 112
- EPLACING THE TAPE DRIVE 113
- Air block plate– 114
- CLEANING THE AUTOLOADER 115
- PRODUCT MANUAL 1012581 116
- TROUBLESHOOTING 119
- SCSI BUS INFORMATION 126
- OPERATING SYSTEM INFORMATION 127
- DIAGNOSTIC INFORMATION 127
- ADVANCED TROUBLESHOOTING 128
- SHIPPING THE AUTOLOADER 129
- Remove this screw 130
- (one each side) 130
- Insert shipping key here 131
- Foam spacers 133
- SPECIFICATIONS 135
- PERFORMANCE SPECIFICATIONS 136
- CARTRIDGE INVENTORY TIMES 137
- MOVE COMPLETE TIME 137
- RELIABILITY 137
- POWER SPECIFICATIONS 138
- ENVIRONMENTAL SPECIFICATIONS 139
- ACOUSTIC NOISE LIMITS 140
- SHOCK AND VIBRATION LIMITS 140
- SHIPPING SPECIFICATIONS 141
- CANADIAN VERIFICATION 142
- EUROPEAN COMMUNITY 142
- USTRALIA AND NEW ZEALAND 143
- APPENDIX A—SPECIFICATIONS 144
- WRITE ONCE, READ MANY 145
- (WORM) CAPABILITY 145
- DATA SECURITY ON WORM MEDIA 146
- WORM MEDIA ERRORS 146
- REQUIREMENTS 147
- TAPEALERT FLAGS 147
- ERROR CODES 148
- ERROR MESSAGES 149
- APE ALERT FLAGS 151
- APPENDIX C—ERROR MESSAGES 154
- PRODUCT LIMITED WARRANTY 161
- ON SITE SERVICE (OSS) 161
- WARRANTY 162
© 2020, manymanuals.fr. Tous droits réservés | 1.483 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels